Garage door interior with track and opener in Arizona
  • Backed Into
  • Bumper Caught Under the Door
  • Door Jammed After an Impact
  • Secured First, Priced Second
  • ROC #310144

Garage Door Hit by a Car in Mesa, AZ

Leave the car where it is, unplug the opener and call. We make vehicle-damaged doors safe across Mesa and the East Valley, check the cables and brackets you cannot see, and write an itemized estimate your insurer can read. A person answers after hours.

The service call is $85, which covers a 22-point inspection and the first half hour of labor. A person answers after hours, and after-hours and weekend work carries a $250 call fee.

  • Women-Owned Family Business
  • ROC #310144
  • Licensed, Bonded & Insured
  • 90-Day Labor Warranty
  • Google Rated
Garage door interior with track and opener in Arizona

If it happened in the last few minutes, the useful part of this page is the next two sections. Leave the door where it is, keep the opener off, and read those before you try anything.

If it happened yesterday and the door has been going up and down since, read them anyway. A door that still runs after an impact is not the same as a safe door, and most of the damage here occurs after the collision.

The Next Ten Minutes

Put the car in park and leave it where it is if any part of it is touching the door.

Moving it is the single worst decision available to you right now, and the next section explains why.

Unplug the opener, or switch off the breaker if the plug isn't reachable.

Not the wall button. The power.

Get everyone out from under the door.

DASMA's figure for garage doors generally ranges from 90 pounds to over 500, and even at the lower end, that is a counterbalanced assembly you don't want to be underneath after an impact.

Look at the cables running down the left and right sides.

If either is slack, hanging loose, or off its drum at the top, treat the door as unsupported and stay out from under it.

Look at the bottom corners.

The bracket where the cable attaches is the part that hurts people. Do not unbolt it, straighten it, or pry at it.

Take photographs before anything moves.

Wide shot with the car in place, then close-ups. The documentation section below covers what to capture.

Then call.

We'll tell you whether the door needs to be secured before anyone uses the garage, and whether it's safe to move the vehicle first.

Garage door interior with track and opener in ArizonaCollision and impact repair, Mesa & the Phoenix metro

The One Thing Not to Do

It is the reflex, and it is the most damaging thing you can do to a garage door in this situation. If a bumper, a tailgate, a roof rack, or a trailer hitch has hooked under the bottom of the door, accelerating away pulls the bottom section, the bottom brackets, and the lifting cables off the door in one motion. A job that was a dented section becomes a job that is a section, both cables, both bottom brackets, and a door that is now off its track.

The same goes for the opener. Do not press the button to see if it still works. That test risks more than it tells you, and the next section lists what it breaks.

What Happens If You Run the Opener Anyway

A bent door in a bent track does not simply refuse to move. It moves badly, and it takes things with it. This is the order it usually goes in.

  1. A lifting cable snaps. Cables under tension do not fall gently. They release, and they can whip.

  2. A bottom bracket cracks at one corner, the one already carrying the damage.

  3. More sections bend. The door tries to fold the wrong way at the curve into the horizontal track, and a one-section job becomes a two- or three-section job. This is how a small collision turns into a new door.

  4. The vertical track twists or pulls off the jamb, taking the fasteners and sometimes part of the wood with it.

  5. The opener's force limit keeps fighting it. The machine senses resistance, reverses, tries again, reverses again. On an older unit, that cycle is a reasonable way to cook a logic board, and now you're buying an opener as well.

All of it is avoidable by leaving the door alone until somebody has looked at it.

The Bottom Bracket, and Why We Keep Mentioning It

The two brackets at the bottom corners of the door are where the lifting cables terminate. They are therefore connected, through the cables and drums, to the spring, and they hold that load whenever the door is down.

DASMA, the door industry's standards body, is unambiguous about them. Because the bottom brackets are connected to the door's springs, they are under extreme tension, and they should be adjusted or loosened only by a trained technician. Many manufacturers now fit tamper-resistant hardware specifically to prevent novices from loosening it.

That is the piece of this page we would most like you to remember, because a collision puts the damage exactly there. The bottom section is what a bumper hits, the bottom bracket is bolted to the bottom section, and the natural instinct after a bump is to have a look at the bent bit.

The Damage That Isn't Visible

The dent is the part you can photograph. It is rarely the part that decides the repair.

  • Cables. A lifting cable can lose a large fraction of its strands, on the order of a third to a half, without looking dramatically different to anybody who doesn't handle them daily. An impact can crush or kink a cable against the track or the drum. What that produces is a cable that works for a while and then doesn't, usually at the worst moment, and usually taking the door off its track on the way.

  • The vertical track at the impact height. Even a small bend catches a roller on every cycle from that point on. It presents itself as a click, a shudder, or a door that hesitates at one spot, and people live with it for months while it wears out its rollers and hinges.

  • The horizontal track. The nearest thing to an authority here is DASMA's warning about weight and obstruction added to a door assembly: the horizontal track can twist, buckle, or deform, with the potential to let the door come out of the track entirely. That advisory is about added weight rather than about impacts, but the failure it describes is exactly what a technician looks for after one.

  • Rollers and hinges next to the strike. The impact scuffs the rollers on either side and usually bends a hinge. Small parts, and the reason a door repaired without them still runs rough afterward.

  • The opener's arm, rail, and header bracket. Not just the logic board. A door shoved backward pulls on the arm that connects it to the trolley, and a bent arm, a cracked bracket, or a rail knocked out of line makes the opener strain, click, or move the door unevenly long after the section has been replaced.

  • Balance. A door shoved out of square doesn't load its springs the way it used to, and a replaced section isn't guaranteed to weigh as much as the old one. A balance check belongs at the end of every collision repair, and it's the step we'd want checked on anyone's invoice, including ours.

Four Patterns, and What Each One Involves

Vehicle impacts are not all the same event, and the pattern tells you a lot before anybody opens a toolbox.

The low push.

A bumper into the bottom section at low speed. Usually that section, sometimes a bracket. This is the version that stays small if the door is left alone afterward.

The hook.

A bumper, hitch, or tailgate catches under the bottom of a door that was still opening or closing. This is where the driving-forward damage happens, and it is the pattern most likely to take cables and brackets with it.

The mid-door strike.

Higher impact point, taller vehicle, or a car that was moving. More sections involved, and track work is likely, because the force lands above the bottom rail where the door is less able to shrug it off.

The track knockout.

The vehicle catches the vertical track or the jamb. Sometimes the door is barely marked, and the track is finished, which is why this one gets underestimated.

Which Insurance Actually Pays

This is the part of the subject that is most consistently answered wrong online, and the wrong answers are often written for a different country.

You backed into your own door. Your auto liability coverage generally does not cover damage to property you own, such as your garage door. The policy this normally falls under is your homeowners insurance, where vehicle impact is typically listed as a covered peril. The practical question is then whether the repair exceeds your deductible, and it's worth getting a price before you decide.

And your car is a separate question with a separate deductible. People routinely miss this. The door goes to homeowners; damage to your own vehicle goes to your auto collision coverage if you carry it. Two policies, two deductibles, two decisions about whether either is worth filing.

If the garage is detached, the door is usually not covered under the dwelling portion of the policy at all. Detached structures fall under a separate part of a homeowners policy, commonly called other structures coverage, with its own limit. Worth naming when you call your carrier, because it changes the answer.

Somebody else hit your door. A delivery driver, a contractor, a visitor, a neighbor's teenager. When the driver is found at fault, their auto property damage liability coverage normally applies because they damaged property belonging to someone else.

An unknown or uninsured driver hit it. Your homeowners policy may cover it, subject to your deductible, and your insurer may then pursue the driver for reimbursement through subrogation if they can be identified.

You rent the house. The door is part of the building, and a renters policy covers your belongings, while the building's structure is covered under the owner's policy, so your own policy will not pay for the door. Tell the landlord or the property manager, because it's their policy and their decision. If you caused the damage, expect to be responsible for it.

We are not insurance advisers and every policy is different, so treat that as the shape of the question rather than an answer about yours. Call your carrier, describe what happened plainly, and ask which coverage applies before you file.

One more thing, because the internet is full of the opposite. There is a lot of published advice about what not to say to an adjuster and how to push a claim harder. We are not going to write any of it. What we will do is document what we find accurately, which serves you better than a strategy and is the only thing that holds up under close scrutiny.

Which perils are covered and which are excluded, and the deductible arithmetic that applies to any damaged section, are on our panel repair page. The routing question above is the part specific to a vehicle.

What to Document While It's Still Fresh

If there is any chance of a claim, this takes ten minutes, and it is the difference between a smooth file and a slow one.

A wide photograph with the vehicle still in position if it is safe to take one.

This is the shot people wish they had later.

Close-ups of the impact point straight on and at an angle so the depth reads.

Photographs of both bottom corners, both cables, and the vertical tracks at the height of the strike.

The manufacturer's label, usually on the inside of one of the sections or on the track.

Brand, model, and date are what make a matching section findable.

A short written note of what happened in your own words, dated.

What time, which direction, roughly what speed, who was driving.

The damage to the vehicle if the vehicle is part of the claim.

What we provide on our side is an itemized estimate: the section or sections, the hardware, the labor, and anything the impact damaged beyond the obvious, separated so an adjuster can read it line by line. Where it makes sense, we will write it in two parts, one covering the repair itself and one covering anything you have chosen to upgrade while the door is open, so nobody has to guess which is which.

Repair the Section, or Replace the Door

The short version, because our panel page works through it properly.

A single section can be swapped when the brand, the style, the gauge, and the color all still match, which, on a door under about ten years old in a current color, they usually do. It stops being the right answer when three or more sections are involved, when the door is old enough that the color has been retired, or when the repair has crept close enough to the price of a new door that you would be spending most of the money to keep the older half.

What we will not do is quote you a section swap and stay quiet about the arithmetic. If the numbers are close, you should hear both.

What Affects the Price

  1. How many sections are involved, which is often one and sometimes several.

  2. Whether the section is still made in that brand, style, gauge, and color.

  3. Cables and bottom brackets, which a hooked or dragged door has almost always damaged.

  4. Track (vertical, horizontal, or both), and whether the jamb took any of it.

  5. Rollers and hinges on either side of the impact.

  6. Whether the counterbalance needs resetting once the door is square again.

  7. Whether the door needs securing on the first visit and finishing on a second, once a section is on order.

  8. Single or double door, because a double door's sections are wider and heavier to handle.

  9. A person answers after hours, and after-hours and weekend work carries a $250 call fee.

  10. Garage door interior with track and opener in ArizonaGarage door service in Mesa, AZ

How the Visit Goes

  1. 1.

    You call, and we'll tell you what to do until somebody gets there. After hours, a person answers.

  2. 2.

    Text reminder before the appointment, and an ETA text on the day.

  3. 3.

    The technician photographs the damage before touching anything, for your file as well as ours.

  4. 4.

    He secures the door and clamps the track before anything is loosened.

  5. 5.

    He checks the cables, the drums and both bottom brackets first, because those decide whether the door is safe to move at all.

  6. 6.

    He checks the track for square along the whole run.

  7. 7.

    He reads the label and identifies the door, which is what makes a matching section possible.

  1. 8.

    You get an itemized estimate, with the repair and replacement options where both apply.

  2. 9.

    You decide.

    Nothing is ordered, and nothing is done until you've approved it.

  3. 10.

    The door gets made safe the same visit wherever it can be, even when a section has to be ordered.

  4. 11.

    On the fitting visit, the section goes in, damaged hardware is replaced, and the door is re-squared.

  5. 12.

    Balance is checked by hand with the opener disconnected, and then the safety reverse is tested under power.

  6. 13.

    You pay by card, check, cash, Zelle, or Venmo. Financing is available through Wisetack.

Garage door interior with track and opener in Arizona

Why Bring Us Out

We look past the dent. Cables, brackets, track and balance, because those are what turn a repaired door into a door that fails again a few months later.

We replace struck brackets rather than straightening them. A bracket with hidden fractures around its bolt holes is not a part to gamble on.

We write the estimate for a reader. Itemized, with the upgrade separated from the repair, and with both options shown when replacement is genuinely competitive with repair.

We won't coach you against your insurer. We'll document what we found accurately and let that do the work.

Any brand, any age, including doors we didn't install and doors whose original installer is long gone. No minimum job or invoice.

Second-generation, family-owned, and here. A Mesa company working on Mesa doors, not a call center routing your job to whoever is closest.

If we get it wrong, we make it right. Ninety days on our labor, and every manufacturer's parts warranty is honored.

Making It Less Likely Next Time

Wait for the door. A great many of these involve a door that was still moving. Modern openers take twelve to fifteen seconds to complete a cycle, which feels much longer than it is when you're already late.

Mark the stop. A hanging tennis ball, a floor stripe, a parking block. It sounds unserious, and it works, particularly with a vehicle that is new to the household.

Check the mirror, not the camera. Backup cameras look at the ground behind the car, and a garage door is above it.

Mind the tall additions. Roof boxes, ladders, bikes and antennas are the reason a vehicle that has cleared that door a thousand times suddenly doesn't.

What Mesa Customers Say

"I made a dumb mistake and backed into my garage door Friday morning. … They explained if I hadn't had the door all the way up taking that bracket off would have been really dangerous. … It took him under a half hour to replace my bracket, and fix my door."
linz HSeptember 2022
See this review on Google

Frequently Asked Questions

I backed into my garage door. Does my car insurance cover it?

Usually not, because auto liability generally excludes damage to property you own, and your own garage door is your property. Vehicle impact is typically a covered peril on a homeowners policy instead. Whether it's worth claiming depends on your deductible relative to the repair cost, so price the repair first. Ask your carrier.

A delivery driver hit my door. Who pays?

When the driver is found at fault, their auto property damage liability normally applies. Photographs, the time, and any company name or vehicle number on the truck are what make that straightforward.

Nobody left a note. What now?

Report it to the police because, in a hit-and-run, they may be able to identify the vehicle and document everything before it moves. Be aware of one catch: in many places, police won't write a report for an incident on private property, so you may be told there's nothing to file. That doesn't stop you from claiming. Your homeowners policy may cover it subject to your deductible, and your insurer may go after the driver later if they turn out to be identifiable. Don't wait on any of that before getting the door made safe.

The door still opens and closes. Do I need to do anything?

Yes, and it's easy to get wrong. A door that still runs after an impact can be running on a damaged cable, a cracked bracket, or a bent track, and all three get worse with every cycle. Have it looked at before you keep using it.

My bumper is under the door. Can I just drive forward?

Please don't. That's the move that pulls the bottom section, the brackets and the cables off the door together. Call and describe what's caught on what; there's usually a safe way to release the door and free the vehicle.

Is a collision repair finished in one visit?

Only where nothing has to be ordered. Where a section is ordered, the door is made safe first, and the section goes in on a fitting visit once it arrives.

Can just the damaged section be replaced?

Often, when the brand, style, gauge, and color still match. Our panel page works through the matching problem in detail and explains when a whole door is the right call.

Will the new section be a different color?

It shouldn't be if the color is still in production. Manufacturers do retire colors, and a door old enough to have faded in this sun is the harder case. We'll tell you what the match looks like before anything is ordered.

Do you fix the wall and the framing too?

We repair the door, the track, and the hardware. The jamb, framing, drywall, and stucco are a general contractor's job on a house, and we'll say so.

Do you bill my insurance directly?

No. You pay us and submit a reimbursement request. We provide the itemized estimate and the photographs your adjuster needs.

Is a bent track always replaced?

Not always, and that's a judgment made at the door rather than from a photograph. A kink, a twist, or a track pulled off the jamb gets replaced, because a bend at the impact height catches a roller on every cycle afterward, and no manufacturer publishes a tolerance you could check it against.

How long does a collision repair take?

Making the door safe is usually well under an hour. The fitting visit typically lasts 1 to 3 hours, depending on how many sections and how much hardware are involved.

Send us a photo of the damage before anything moves.

Wide shot, close-up, and the manufacturer's label if you can find it. That's usually enough for us to tell you whether this is a section, a section plus hardware, or a conversation about a new door.

Request an Estimate

Step 1 of 2