Garage Door Service in Tempe, AZ
Repairs, openers and new doors for Tempe homes, including the tilt-up doors, extension springs and discontinued sections common in older houses. Second-generation, women-owned, ROC #310144, with free phone quotes.
Office hours are Monday to Friday, 7:00 a.m. to 3:00 p.m. A person answers after hours, and after-hours and weekend work carries a $250 call fee.
- ROC #310144
- Licensed, Bonded & Insured
- Women-Owned Family Business
- 90-Day Labor Warranty
- Google Rated

Tempe has some of the oldest garage stock in the East Valley. Four in ten Tempe homes were built before 1980 and one in six before 1970, which means we find things behind Tempe doors that have not been made in decades.
That is simply a different kind of visit, and it is worth knowing which one you are booking.
What the Census Says About your Garage

On the U.S. Census Bureau's American Community Survey 2024 five-year estimates, the median Tempe home was built in 1984. Of Tempe's roughly 86,000 housing units, 41.2 percent predate 1980 and 17.0 percent predate 1970.
Set that against Gilbert, where the figure is 4.1 percent. Tempe has ten times Gilbert's share of pre-1980 housing, which is not a small difference when we open a door.
Four things we still find regularly in Tempe and almost never in the newer towns:
One-piece tilt-up doors. A single slab that swings out and up on pivoting arms, so there are no sections and no horizontal track above your car. They were standard on valley houses into the 1970s and plenty of them are still working, which is a reasonable argument for how well they were made. We service them. Parts are a conversation, and hardware is generally easier to find than a replacement slab.
Extension springs. The long springs that run horizontally above the tracks on either side, with no torsion bar across the opening. They work, and we work on them. The safety question with an extension spring is whether it has a containment cable running through it, because a spring that lets go without one is a projectile.
Openers with no photo eyes. External entrapment protection has been required on residential garage door openers manufactured on or after January 1, 1993. The rule allows a photo eye or an edge sensor, and photo eyes are what the industry settled on. An opener with neither is either old enough to predate the requirement, which is not a rare find in a city where four in ten houses were built before 1980, or a newer one whose sensors have been removed, unplugged or bypassed, which we see just as often. Either way, it is the one thing on this page that changes what we are willing to do, which is why it has a section of its own below.
Sections that are no longer made. More below, because it is the thing that most often changes a Tempe quote.
Garage door service in Tempe, AZThe Line we do not Cross, and Why it Comes up in Tempe
If an opener has no working photo eyes, we will not touch the motor.
That is a firm position, and it costs us work, so it is worth explaining.
An opener with no working photo eyes has no photoelectric protection across the opening, whatever its age. It stops when the door meets enough resistance, and how much resistance there is depends on how the force settings were left, possibly decades ago. There is no beam across the opening to tell it a child or a dog is underneath.
We are happy to work on the door: springs, cables, rollers, track, sections, balance. What we will not do is service the head of an opener that has no way of detecting something in the opening and then hand it back to you as a working machine, because at that point we have put our name on it.
What we will do instead is tell you plainly what you have, quote you a replacement opener, and, if the door itself is sound, leave the door in better shape than we found it either way.
This comes up in Tempe more than anywhere else we work, for exactly the reason under What the Census Says About Your Garage, above. If your opener has no small sensors mounted near the floor on both sides of the opening, this is the conversation we will have.


The Parts Question
On an older Tempe door, the part that can hold a repair up is a section.
Garage door sections are made to a profile, and profiles get discontinued. When a manufacturer stops making a design, the replacement section for a door built in 1988 is not sitting on a shelf. Depending on the door, the options are a compatible section that will not match perfectly, a universal replacement section where one exists for that manufacturer, or a new door.
What we do about it. We identify the door before we promise anything. There is usually a label, often on the inside of an end stile or the back of a section, and where there is not, the hardware and the section profile will usually tell us the maker. Then we tell you which of the three options you actually have.
When one section is damaged and the rest are sound, a single-section replacement is often the right call. When the sections have started to delaminate, or the door has been repaired twice already, replacement is usually the honest recommendation, and we will say so.
Do You Need a Permit in Tempe?
Tempe publishes an exemption list, and a garage door is not on it.
Tempe's single-family residential page gives no permit answer in its own text. It tells you to email the Permit Center. But the Tempe Administrative Code, adopted into the city code and linked from Tempe's building code page, includes a section titled "Work exempt from permit," and it is a closed list. It opens with the words "permits shall not be required for the following," and anything not named is not exempted by it.
What is on it: detached accessory structures up to 200 square feet, fences up to 7 feet, retaining walls up to 4 feet, sidewalks and driveways, painting, tiling, cabinets and countertops, replacement roof covering, small decks, window awnings, and playground equipment.
What is not on it: doors of any kind. Windows. Low-voltage wiring for a garage door opener.
One live detail. Tempe adopted the 2024 International Codes effective July 1, 2026, with a transition period through December 31, 2026, during which applications may be submitted under either the 2018 or the 2024 codes. If your project has a permit in it, that transition is worth asking about.
So we are not going to tell you a Tempe door swap is exempt. There is statewide guidance from Arizona Building Officials, the state association of building officials, that treats door replacement with no structural change as permit-exempt, but AZBO is an association and Tempe's adopted list is what governs in Tempe.
The Tempe Permit Center is at (480) 350-4311 and permitcenter@tempe.gov. Their answer beats ours, and it beats anyone in this trade who tells you confidently without having read the list.
Dust, and One Thing Tempe Has Going for It
The National Weather Service's Phoenix office states that during an average year, generally one to three dust storms move into the Phoenix area, predominantly from the southeast, usually lasting ten to thirty minutes, though dusty conditions can remain for some time afterward.
The next part is our rule of thumb rather than the Weather Service's. If the events arrive predominantly from the southeast, a south-facing or east-facing door should take more of the abrasive load than a north-facing one on the same street. That is our inference from the direction, and on an older Tempe door where the weatherstripping may well be original, it is where we look first.
If your door faces south or east, its seals and rollers take more of the dust, so that is where we look first on an older Tempe door.
What we Get Called Out for in Tempe
Springs, in both families. Torsion on the newer stock, extension on the older, and the two are not interchangeable jobs. If you have extension springs without containment cables, we will raise it regardless of whether you called about the springs.
Openers at the end of the line. See The Line We Do Not Cross, and Why It Comes Up in Tempe.
Sections and panels. See The Parts Question.
Doors off track. Older tracks, older rollers, and more years of small impacts add up. If your door has come off its track, stop using it and do not pull the emergency release while it is up, because the door's weight is being held by something that is no longer holding it the way it was designed to.
Balance. An old door on tired springs sits unevenly, drags on one side, and works the opener harder than it should. A balance check is quick and is the thing most often skipped; on older stock, it is frequently the actual cause of the complaint someone called about.
Weather seals that have simply run out. A bottom seal is a wear item, and an original one on a 1970s door has done its time. Replacing it makes a noticeable difference to what ends up on the garage floor.
Commercial and industrial work. Commercial and dock work is scheduled, so it books differently from a repair call.
Replacing an Old Tempe Door is not the Same Job as Replacing a New One

On a twenty-year-old tract house, a replacement door goes into the same opening on the same kind of track and the job is largely predictable. On a fifty-year-old Tempe house, it is not, and three things come up that are worth knowing before you get a quote.
Headroom. The distance between the top of the opening and the ceiling decides which track and which opener can go in. Older garages were not built with modern hardware in mind, and some have less headroom than a standard installation needs. There are low-headroom track configurations, and there are jackshaft openers that mount on the wall beside the door. The jackshaft has a condition attached that gets skipped a lot: it drives the torsion shaft directly, so it needs a torsion spring system and clear wall space beside the door. On an extension-spring door, that means the spring conversion below comes first. It is usually solvable. It is not always solvable with a standard installation, which is why we measure rather than quote from the driveway.
Going from one-piece to sectional. If you have a one-piece tilt-up door and you want a sectional, that is not a swap. The two use different hardware, tracks, and opening geometry, and the old pivoting arms and jambs have to come out. It is a good upgrade, and people are usually happy with it. It is a bigger piece of work than swapping a door, and you should hear that from us at the quote stage.
Going from extension to torsion. Plenty of older Tempe doors run on extension springs. Converting to a torsion spring on a bar above the opening is a real improvement in how the door behaves and in what happens if a spring fails, and it needs headroom and a solid header to mount to. We do this conversion, and we will tell you honestly whether your opening suits it.
What does not change: the door still has to balance. A new door hung on the wrong spring is a worse door than the old one, and the balance check at the end of the installation is not optional.
The Same Boundaries Here as Everywhere
What we do: garage doors and openers, residential and commercial, including doors and openers we did not install, whoever made them, and however old.
What we do not do: locks, handles, or rekeying, which are locksmiths' jobs. A new outlet or circuit for an opener, which is an electrician's job before ours. Jambs, framing, drywall, and stucco after a collision, where the door is ours, but the surrounding building is not. Garage screens, and retrofitting windows into an existing door. Mobile and manufactured homes. The motor on an opener with no photo eyes, as above. And home warranty dispatch, which we are not taking on right now.
There is no minimum job.
Frequently Asked Questions
My garage door is a single solid slab that swings out. Do you work on those?
Yes. That is a one-piece tilt-up door, and there are plenty still working in Tempe. Hardware and springs are generally available. A replacement slab is a bigger conversation.
Do I need a permit to replace a garage door in Tempe?
Tempe publishes an exemption list in its Administrative Code, and doors are not on it. Because that kind of list is closed, we will not tell you a door swap is exempt. Call the Permit Center at (480) 350-4311 and ask, and note that Tempe is running a transition between the 2018 and 2024 codes through the end of 2026.
My opener works fine. Why won't you service it?
If it has no photo eyes, it has no way of detecting a person or an animal in the opening. Working is not the same as being safe, and we will not put our name on the head of a machine like that. We will happily quote you a replacement, and we will still service the door.
Can you match a single damaged panel on a door from the eighties?
Sometimes. It depends on the manufacturer and the profile, and the first step is identifying the door.
Is it worth putting a new opener on an old door?
Often, yes, and sometimes it is worth checking the door's balance first. A new opener on an unbalanced door works harder and fails sooner.
Can you convert my extension springs to torsion?
Often, yes. It depends on the headroom above the opening and on having something solid to mount the bar to. We will measure and tell you rather than guess.
What are extension springs, and do mine need replacing?
They are the long springs that run horizontally above the tracks on either side of the door. Whether they need replacing depends on their condition. Whether they have containment cables is a question about your safety, and we check it either way.
What Customers Say
"Excellent service, on time, expertly done… Been using these folks for years and continue to recommend them highly!"
Every Service in Tempe
Seven of our services have a page written for Tempe homes, because a 1970s Tempe door and a 2015 Gilbert door are not the same repair.
Garage Door Spring Repair in Tempe
Extension springs, containment cables, and what to ask for on a tilt-up.
Garage Door Opener Repair in Tempe
What a new head needs from an old garage before it will hang there.
Emergency Garage Door Repair in Tempe
On a door worked on for fifty years, the first job is finding what is holding it up.
New Garage Door Installation in Tempe
Older Tempe garages were framed to sizes nobody stocks now.
Garage Door Tune-Up in Tempe
Where the parts went on at different times and by different hands, several of the twenty-two points are settled by reading the door against itself.
Garage Door Roller Replacement in Tempe
The smallest moving part on a sectional door, and it gets quoted with the hinge and the track it runs against.
Garage Door Weather Seal Replacement in Tempe
New rubber goes on either way. What the old strip looks like when it comes off determines whether that was the whole job.
The rest of the catalog reaches Tempe too, on the same terms. Our garage door repair hub is the full list, and our new doors and openers hub covers buying.
And the rest of what we do in Tempe. Each link below goes to the valley-wide page unless it names Tempe.
Repairs. Garage door repair covers all of it: springs, openers, cables and tracks, off-track recovery, panels, rollers, safety sensors, weather seals, balance and realignment, noisy doors, collision damage, lockouts and remote and keypad programming. Emergency repair is the same list after hours and on weekends, at the $250 call fee.
New doors and openers. New door installation and opener installation, plus custom doors and the four ways to buy a door: steel, faux wood and composite, full-view glass and carriage house. Also insulation, panel reinforcement, high-cycle springs, extension-to-torsion conversion, high-lift and jackshaft conversion, and RV and oversized doors.
Maintenance. The 22-point tune-up, which is the same inspection a service call includes, booked on its own instead.
Commercial. Overhead door repair, operators, roll-up and rolling steel, sectional steel, loading dock doors, dock levelers, seals and bumpers, and self-storage doors. Our commercial hub is the way in.
We do not do locks and rekeying, electrical work, jamb, framing, drywall and stucco, and we do not work on mobile or manufactured homes. Those boundaries are the same in Tempe as everywhere else we go.
Where We Work
Garage door repair and service across the Phoenix metro:
- Mesa,
- Gilbert,
- Chandler,
- Tempe,
- Scottsdale,
- Phoenix,
- Queen Creek,
- Apache Junction,
- Glendale,
- Peoria,
- Ahwatukee,
- Fountain Hills and
- Paradise Valley.
Older door, older opener, or something you cannot identify? That is the call we like.
Tell us roughly when the house was built and what the door is doing, and we can usually tell you what we are walking into.



