High-Lift and Jackshaft Conversion in Mesa, AZ
Get your garage ceiling back for a car lift, a tall vehicle or storage. We measure headroom, door weight and the torsion bar before we quote high-lift track or a wall-mount jackshaft opener. Phone quotes are free, and an in-person measure is $35.
- Women-Owned Family Business
- ROC #310144
- Licensed, Bonded & Insured
- 90-Day Labor Warranty
- Google Rated

If you have put a car lift in and the door now fouls it, if you want to park something tall under a door that stops too low, or if you need the ceiling back for storage and the opener rail is in the way, this is the job. Your door comes off standard track and goes up before it comes in.
Three Ways a Door Gets Out of the Way
Every sectional door does the same trick: it goes up, then it turns and runs back into the building. Two of the three differ in where that turn happens and the third in where the motor lives, and that is what decides what you can park, store, or install underneath.
Standard lift.
The door rises roughly its own height and turns immediately, running back along the ceiling just above the opening. It is what almost every house in this valley has; it uses the least headroom, and the horizontal track sits exactly where a car lift, a loft, or a tall vehicle wants to be.
High lift.
The door rises well past the top of the opening before it turns, so the horizontal track lives higher up, and the open door sits clear of the space underneath it. The amount of extra vertical travel is the "lift" in the name, and it is a value someone has to measure.
Jackshaft, on the wall.
This one is not about the track at all. The opener comes off the ceiling and mounts beside the opening, driving the torsion shaft directly, which frees the whole center run of ceiling. On a tall door, it is often the answer, and it is frequently installed together with high lift.
| Standard lift | High lift | Jackshaft on the wall | |
|---|---|---|---|
| What it changes | nothing; it is the default | where the door turns | where the motor lives |
| Headroom needed | least | most | same as whatever track it serves |
| Frees the ceiling | no | partly, above the opening | yes, the center run |
| Needs a torsion shaft | no | no | yes, always |
| Drums change | no | yes | no |
| Spring respecified | no | yes | only if the drums changed |
| Published size ceiling | none | the structure above the opening | 14' × 18', 180 sq ft, 54" of lift |
The two are separate purchases, and people constantly conflate them. High lift changes where the door goes. A jackshaft changes where the motor goes. You can have either, both, or find out that your door will take neither.
High-lift and jackshaft conversions, Mesa & the Phoenix metroWhat High Lift Changes Behind the Door
A conversion is not a bracket swap. Raising where the door turns changes the counterbalance geometry, so the drums, cables and springs change with it, and sometimes the shaft too.

The drums change, and this part is not optional. A cable drum is grooved for a specific amount of cable travel. On high lift, the cable has farther to go, so the drum is a different part with a different profile. Fitting high-lift track and keeping standard drums is not a compromise; it is a door that will not sit where it should at either end of its travel.
The cables change because they are cut to length for the travel they serve.
And the springs are respecified. A spring set is calculated for a door of a given weight on a given drum. Change the drum and the moment arm changes with it, so the spring that balanced your door perfectly on standard track is the wrong spring for the same door on high lift. This is the single most common thing a hurried conversion skips, and the symptom is a door that is heavy at the floor, light at the top, or will not hold where you leave it. Our spring repair page covers how a spring is specified from real weight.
The shaft may need to be longer, and on a wide opening it may need an intermediate bearing.
What does not change is the door itself. The sections, hinges, and rollers are usually the same ones you already own, which is why this job is worth doing at all on a sound door.
One consequence worth knowing before you commit. Raising the door means the top section finishes its travel farther from the opening, so anything mounted on the inside face of that section goes up with it. On a door with a strut across the top, a bracket for an old rail, or a hand-fitted shelf above the opening, those are things to point out when the technician measures, before the day.
The Prerequisite Chain, in the Order It Fails
A jackshaft conversion has published requirements; they are specific, and they fail in a predictable order. These are LiftMaster's own installation requirements for its residential jackshaft units, which is the line we fit.
1. A torsion system.
The opener drives the torsion shaft. No shaft, no jackshaft. The next section is about what to do if your door is on extension springs.
2. A one-inch torsion bar.
Not every door has one.
3. At least 8.5 inches between the side wall and the end of the bar, for the unit to occupy.
4. The bar extending at least an inch and a half past the bearing plate.
5. No more than 54 inches of high lift.
If your ceiling needs more lift than that, the jackshaft is out, and the conversation becomes a different opener.
6. Door no taller than 14 feet, no wider than 18 feet, and no more than 180 square feet.
All three, not whichever is convenient.
7. Track radius of 15 inches, with 12 inches the minimum.
8. Then the drum sets the weight ceiling.
A 3- to 3.9-inch drum supports a door up to 430 pounds. A 4- to 6-inch drum supports up to 850 pounds. On a wood or oversized door, this is the limit that trips people up, because the door's weight is the one specification not written down anywhere in the garage.
Read that list as eight separate ways a confident quote can be wrong. Three of the eight you can check yourself before you call, and in this order: whether the shaft is one inch, what the gap is between the end of the shaft and the side wall, and whether the door is taller than fourteen feet or wider than eighteen. Those three are the ones a tape measure settles before anybody comes out. Our opener installation page has the wall-mount basics if you are still deciding between a wall unit and a ceiling one.
If Your Door Is on Extension Springs, Read This First
A jackshaft opener drives a torsion shaft, and an extension-spring door does not have one. The springs run horizontally above the tracks; there is no bar across the opening, and there is nothing for the opener to turn.
So the job grows. Converting the counterbalance to torsion becomes part of the work before the opener can be installed at all, so an extension-spring door is two jobs quoted as one. Our spring conversion page sets out what that conversion involves, what the standard actually requires of an extension-spring door, and when converting is not the answer.
How to tell which you have in about five seconds. Look above the door. A bar running the full width of the opening with one or two springs wound around it is torsion. Two long springs stretched along the horizontal tracks, one on each side, with no bar across the middle, is extension.
What We Measure Before We Quote
Six numbers, and a quote that skips them is a guess.
Headroom: the space from the top of the opening to the lowest thing above it, which may be the ceiling or may be a truss, a duct, a light, or a sprinkler line.
The lift you actually need, which comes from the thing you are trying to park or install, not from a round number.
Side room beside the opening, both sides, because the jackshaft needs one of them.
Backroom: the run available behind the opening for the horizontal track at its new height.
The door's real weight, which decides the drum, and therefore the spring, and therefore whether the opener on the list is the opener you can have.
What the roof structure above the opening actually is. A shop or an RV garage is where this stops being a formality: our RV and oversized doors page covers what a ceiling-mounted opener needs from a roof, and a jackshaft sidesteps most of it by driving the shaft instead.
You can give us most of this on the phone, and that call costs nothing. Width, height, what you are fitting under the door, and whether there is a bar above the door. If the numbers look promising, a technician comes to measure properly, and that visit costs $35.
When the Answer Is No
When the headroom is not there. High lift requires vertical space above the opening, and no amount of hardware can invent it. On a garage with the ceiling close to the top of the door, the honest answer is that the door cannot go higher.
When the lift you need is more than 54 inches, and you wanted a jackshaft. Those two requirements collide, and one of them has to give.
When the door weighs more than the drum will carry. The two drum figures are in the prerequisite list above.
When the structure above the opening will not take it. We do not do structural work, and a conversion that hangs new load on something unsuitable is not a job we will quote.
When the door will not justify the hardware. A conversion puts new track, new drums, new cables, and a new spring set onto sections you already own. If those sections are cracked, delaminating, or already patched, the hardware is going onto the wrong half of the door, and a new door on high-lift track from the start is the one we would do. We will say so, and our new doors page covers that path.
And when the opener has no photo eyes. An opener built before 1993 predates the federal entrapment rule, and the motor on one of those is work we decline, whatever else is being asked for. We will still service the door itself, and a replacement head is a conversation we can have.
How the Conversion Goes
- 1.
You call, or you send the numbers.
Width, height, headroom if you can reach it, and what you are trying to fit.
- 2.
A technician measures.
All six numbers listed above, including the door's real weight.
- 3.
You get an estimate by email before anything is ordered, listing the track, the drums, the cables, the spring set, and the opener separately, so you can see what the number is made of.
- 4.
Anything made to order takes a 50% deposit.
High-lift drums and a respecified spring set are frequently special-order parts.
- 5.
On the day, the door comes down to its hardware.
Old track off, high-lift track on, new drums, new cables, the spring set wound to the recalculated figure.
- 6.
He balances it by hand with the opener disconnected, because that is the only test of whether the new spring set is right.
- 7.
The opener goes on, and the force and travel limits are set to the new geometry.
- 8.
The safety reverse and the photo eyes are tested before anybody leaves.
What Affects the Price
We publish a short list of figures and no others, so here is what moves the rest.
Whether the counterbalance has to be converted first. On an extension-spring door, that conversion is part of the work before the track can go up.
How much lift you need. More vertical travel is more track, longer cables, and a different drum.
The door's weight, which drives the drum size and the spring set, and on a wood or oversized door drives them a long way.
Whether the opener is included. A jackshaft unit is a separate purchase from the track work, and plenty of people do one without the other.
Garage door service in Mesa, AZWhat is on the truck and what has to be ordered. We carry the common parts. High-lift drums for a specific door weight usually are not among them, and an ordered part has a lead time we will not invent a date for.
Financing is available through Wisetack. Our financing page covers how that works.
Frequently Asked Questions
Can any door be converted to high lift?
No. It needs the headroom, a sound door, and a structure above the opening that will carry the track at its new height. The six measurements above settle it, and you can check the door's width, height and whether there is a torsion bar above it before you call.
Do I need a jackshaft opener if I go to high lift?
Not necessarily. A ceiling-mounted opener can work with high-lift track, and whether it does depends on how much lift you have taken and what is left of the ceiling. A jackshaft becomes the answer when the ceiling is genuinely unavailable.
Can I keep my existing opener?
Sometimes, on a high-lift conversion. Never, if the plan is to move the motor to the wall, because a jackshaft is a different unit that drives the door differently.
Will the door be noisier?
It should not be, and if it is, something is wrong. A respecified spring set on a correctly aligned track should be no louder than what you had. Our noisy door page covers what actually makes the noise.
How much ceiling do I get back with a jackshaft?
The center run that the rail and the motor occupy, which on a typical double garage is most of the usable depth above the car. That is the whole reason people fit them.
My garage has a cathedral ceiling. Does that help?
It usually makes the opener question easier and the track question harder, because high-lift track has to be supported along its run and a sloping ceiling gives it less to hang from at a consistent height.
Is this something I can have done at the same time as a new door?
Yes, and the spring set is being specified from scratch regardless. Our new doors page covers that side.
What if I am converting because I have installed a car lift?
Tell us the lift's make and its fully raised height on the first call. That figure, not the door, is what sets the lift you need.
Does high lift make the door harder to open by hand?
It should not, if the spring set was recalculated properly. A correctly balanced door requires roughly the same effort on high lift as on standard track, because the spring does the same work against the same weight. A door that got heavier after a conversion is telling you the spring was not respecified, and it is a finding we have made on other people's high-lift work.
Can the track be put back to standard afterward?
Yes, and it is the same job in reverse, with the drums, cables and spring set specified back to standard, which is worth knowing if you are converting for something temporary like a project car rather than for a vehicle you intend to keep.
What Customers Say
"Lou is great! He came out on Christmas Eve and installed a new motor. … This wasn't the first time I used this company for my old garage equipment"
Where We Work
Garage door repair and service across the Phoenix metro:
- Mesa,
- Gilbert,
- Chandler,
- Tempe,
- Scottsdale,
- Phoenix,
- Queen Creek,
- Apache Junction,
- Glendale,
- Peoria,
- Ahwatukee,
- Fountain Hills and
- Paradise Valley.
Tell us what you are trying to park, store or install under the door.
That answer sets the lift, and the lift sets everything else. Width, height, and whether there is a bar above the door get you a useful conversation on the phone, free.



