Garage door installed on an Arizona home in Phoenix, AZ
  • Bottom Seals
  • Side Seals
  • Thresholds
  • ROC #310144

Garage Door Weather Seal Replacement in Phoenix, AZ

Keep heat, dust, water and pests out of your Phoenix garage. We replace bottom seals, side and header seals and thresholds on any brand, and reset the opener so the door closes cleanly.

A quote over the phone is free. A service call on a failed door is $85, covering the 22-point inspection and the first half hour of labor; after hours and weekends it is $250; a quote visit is $35.

  • ROC #310144
  • Licensed, Bonded & Insured
  • Women-Owned Family Business
  • 90-Day Labor Warranty
  • Google Rated
Garage door installed on an Arizona home in Phoenix, AZ

A bottom seal does not seal on its own. It closes against a slab at the bottom and a wood frame up the sides, and both are parts of the building.

So, on a Phoenix seal call, the rubber is the second question. The first is what it has to close against, because a surface that has cracked, lifted, or settled leaves a gap that no profile will fill.

The Four Parts, and Which Belong to the Door

Two are on the door, and two are on the building, and that distinction decides who fixes what.

  • On the door: "Astragal" is the trade name for the bottom seal and the term DASMA uses. It sits in the astragal retainer, an aluminum channel fixed to the bottom edge. The astragal wears out; the retainer usually survives.

  • On the building: The side and header seals fix to the wood the door closes against, and DASMA's term for that sealing component is stop molding, with door stop, jamb seal, and side seal listed as the same thing. The fourth part is not a seal at all: a threshold is a rubber strip bonded to the slab that the bottom seal then presses onto, so it changes the surface.

  • Which is why the order matters. The part is ours; the slab and the frame are the building's. So the surface gets established first, and then there are three ways this ends: new rubber, a change to the surface, or another trade's work.

Garage door installed on an Arizona home in Phoenix, AZWeather sealing in Phoenix, AZ

The Floor Under the Landing Line

A slab goes out of true three ways. It cracks and one side lifts. It settles into a dip. Or it was never flat, having been poured, cut, and patched.

  1. What a seal can and cannot follow: It accommodates a small amount of unevenness, especially in a hollow bulb profile rather than a flat-faced one. What it cannot do is bridge a dip, which is why the slab gets read along the full landing line.

  2. And it gets read in two directions, across the width and front to back, because a seal that closes at one end and stands off at the other is describing what is underneath it, and a dip under the landing line moves the contact point away from where the door was set to stop.

  3. One Phoenix case is different: a drive that falls away from the opening by design is the foothills question, and our Ahwatukee page covers it.

The Frame Side, Which Is the Other Half of the Surface

The sides and header are the same problem stood on end, where the substrate matters more than the rubber.

  • Two constructions, two different jobs: Either a flexible strip is nailed to the wood already on the jamb, or the wood and the seal are a single profile in a single piece. Which you have is read off the opening.

  • A nail-on strip needs something to nail into. Fastener holes in stop molding pack out, and a strip driven back into a packed hole does not hold. Where the wood is split, chalky, or coming away at the jamb, the failure is in the molding, and the job is whole stop molding with an integral seal, which is work we do.

  • And the boundary sits at the frame. If the jamb is out of plumb or the framing behind it has moved, the sealing plane has moved with it, and no molding profile squares that up.

Where the Answer Is Concrete

  1. Ours on this job: the astragal and its retainer, the side and header seals, the whole stop molding, including the wood, and a floor-mounted threshold bonded to the slab. Any brand, any age, doors we did not install.

  2. Outside our scope: concrete. Repairing, grinding, leveling, or replacing a slab is not our trade, and neither is the jamb or framing. Also locks and rekeying; any new outlet or circuit, which is an electrician's job before ours; mobile and manufactured homes; the motor on an opener with no photo eyes; and home warranty dispatch, on hold at present.

If the real fix is concrete or framing work, the estimate says so and leaves it unpriced, so you can take it to the right contractor. There is no minimum job.

The Profile Is the Last Decision

Once the surface is known, the part follows from the channel it keys into and the degree of irregularity it must accommodate.

  • The profiles are not interchangeable. A T-style seal keys into a slotted retainer, and a bead-style into a two-slot track; neither fits the other's channel. Bulb or U-style is hollow, so it follows an uneven floor better. Where there is no retainer, the seal fixes straight to the bottom rail.

  • One manufacturer puts a number on the surface. Martin picks its bottom seal by how far out of level the floor is. The one-inch standard suits a floor roughly an inch out, with a taller seal for floors farther out of level. So the size is a measurement.

  • Name the family before the part. On a sectional door, the astragal sits in a retainer fixed to the bottom section. A one-piece tilt-up is a single slab on pivot arms with no sections, so what the seal fastens to is read off the door. We service both families.

What Gets Read Off the Slab

Every Phoenix slab is different, so we read yours before choosing a seal.

A Phoenix address does not tell us when the slab was poured, whether it has moved since, whether the opening has been altered, or which family the door is.

The one interval with a manufacturer behind it. Clopay states that seals should be checked and replaced every 2 to 3 years, depending on climate and use. That is national, and the only manufacturer-published figure we have located, and it is a prompt to look at the door rather than a date to work to. Our weather seal page sets out what new rubber actually fixes and what it does not.

Phoenix Weather Seal FAQ

Can you quote a threshold over the phone?

Not that part. Whether you need one is a measurement off your floor, and the free phone quote cannot do it.

The concrete under my door has cracked and lifted. Can you still seal it?

Sometimes, and the answer comes from looking. A taller or hollow profile accommodates more irregularity, and a bonded threshold changes the surface the seal meets, though it requires sound concrete to bond to. Where the slab needs repair first, that is a concrete contractor's job.

Is a threshold part of the door?

No. It is bonded to the slab, so it stays behind if the door is replaced.

Which fee applies if I only want somebody to look at the opening?

That is the $35 in-person quote visit. The $85 service call is for a failed door, and after hours or on a weekend, it is $250. A special-order seal takes a 50% deposit.

My door is one solid slab that tilts out. Does it take the same seal?

Not necessarily. A one-piece tilt-up may have no retainer channel, in which case the seal fixes to the bottom rail. We work on both families.

How the Visit Goes

  • On arrival, after the text reminder and ETA, we watch where the door lands before anything is touched, read the slab along the landing line, measure the retainer profile, and look at the stop molding. The estimate is written and emailed before work starts, and the work follows the approval.

  • Before we leave. The replacement seal is thicker than the worn one that comes off, so the door now meets the floor earlier than the opener's learned limit was set for. The close limit and the force setting are reset, the safety reverse is tested, and the balance check is performed, all of which occur on every visit.

What Customers Say

"I needed some hard to find bottom seal for my Martin garage door and I called Quality Overhead Door to see if they had it. Dennis knew exactly what I was talking about and had it ready for me when I arrived. Joani got my bill settled quickly and I was on my way. They saved me a bunch of time and headache with great customer service. Thank you, QOD!"
Gordon AApril 2025

Where We Work

Garage door repair and service across the Phoenix metro:

See the full service area

Close the door in daylight, stand inside, and look along the full width.

Tell us where the gap is and whether it is even end to end, then whether the concrete under the door has cracked, lifted, or dropped. Not knowing is an ordinary answer, and it still shapes what the technician brings.

Garage door installed on an Arizona home in Phoenix, AZ