Garage door installed on an Arizona home in Phoenix, AZ
  • Door Opens, Will Not Close
  • Photo Eyes on Any Brand
  • Openers We Did Not Install
  • ROC #310144

Garage Door Sensor Repair in Phoenix, AZ

Door goes up but won't come down? It is usually the safety sensors. We clean, realign, rewire and replace photo eyes on any brand of opener in Phoenix, and test the safety reverse before we leave.

A quote over the phone is free. A service call for a failed door is $85, covering the 22-point inspection and the first half hour of labor. After hours and on weekends, it is $250. If you want a technician to look at the garage before anybody commits, that visit is $35.

  • ROC #310144
  • Licensed, Bonded & Insured
  • Women-Owned Family Business
  • 22-Point Inspection
  • Google Rated
Garage door installed on an Arizona home in Phoenix, AZ

The two small units bolted near the floor on either side of your door opening are a part with a start date. Federal rules put them there, and those rules begin on a particular day, so there are openers that were never required to carry a pair and do not have one.

So on a door that goes up and refuses to come down, the first question is not which light is lit. It is whether there is a pair down there at all.

The Part Has a Start Date, and Here It Is

The federal standard for these machines is 16 CFR part 1211, and its first section is an effective date. It reads: this standard applies to all residential garage door operators manufactured on or after January 1, 1993, for sale in the United States.

  • What the standard then requires is entrapment protection. For a door that moves vertically, the devices it lists are an external photoelectric sensor, an external edge sensor, or another device that provides equivalent protection. Photo eyes are what the industry settled on.

  • Behind the requirement is a count the Consumer Product Safety Commission published: since 1982, 48 children between the ages of two and 14 died after becoming entrapped under doors with automatic openers.

  • The consequence for your door is narrow, and it is useful. A standard that applies to operators manufactured on or after a date says nothing about one manufactured before it. An opener built before that day was never required to carry a secondary device, and owning one today breaks no rule. It also means you have to go and look before any of this helps, because half of what follows describes a part that may not be there.

Our Phoenix page carries the city's housing-age figures and what they predict and what they do not.

Garage door installed on an Arizona home in Phoenix, AZSafety sensor repair in Phoenix, AZ

What the Same Rule Says About a Fault

The rule also tells the opener what to do about a fault, and that is the paragraph explaining the behavior people call us about.

The operator must monitor the device's presence and proper operation at least once during each close cycle. If the device is absent, or a fault stops it from sensing an obstruction, including a break or short in its wiring, then on a vertically moving door the closing door has to open, and an open door may not travel more than one foot below its uppermost position.

That is a description of your evening. The door rises; the door will not descend; nothing looks broken. The machine has run its check, failed it, and refused the one movement that could hurt somebody. The refusal is the system working.

Those sections were last amended by a rule effective May 13, 2024, that revised the testing of photoelectric and edge sensors. The start date is unchanged.

Scope on This Job

  1. Ours: the photo eyes, their brackets and their mounting height, the low-voltage run that feeds them, the opener's force and travel settings, the balance check and the safety reverse test. Any brand, and openers somebody else installed.

  2. Outside our scope: the motor on an opener with no photo eyes. A new outlet or circuit, which is an electrician's job before ours. Locks, handles and rekeying. Jambs, framing, drywall and stucco. Mobile and manufactured homes. Home warranty dispatch, on hold at present.

  3. And one boundary that is ours by choice. We do not bypass, disable, or defeat a photo eye for convenience or on request, and we do not raise a pair to clear something parked in the beam. The mounting height is the whole point of the part.

Phoenix sits within our repair map, and we do not have a Phoenix location, as our Phoenix page states. There is no minimum job.

Three Doors, and One of Them Is a Sensor Repair

Everything above sorts a call into three. They look identical from the driveway and are not the same piece of work.

  1. A pair that is present and faulting. Lenses, aim, brackets, the wiring run, a unit that has given up. This is sensor repair, and the ordinary case.

  2. A pair that was there and is gone. Eyes taken off, unplugged or wired out of the circuit at some point by somebody. Putting a working pair back on the door is a real job, and we do it on any brand. We reinstall missing photo eyes on any brand.

  3. No pair, and no sign there was ever one. Then the subject changes from sensors to the head on the ceiling. On a unit with no external entrapment protection, the honest recommendation is a replacement and not a repair, and our own line is shorter than the regulation's: no photo eyes; we do not touch the motor. We will still service the door and quote you a replacement head.

Which of the three you have takes a look at the door. A phone call tells us which visit to book.

When the Pair Is There and Not Working

A working pair is a beam between two aimed units with power at both ends, so the failures are of aim, of surface, or of supply.

  • Height first, because it is the one specification with a number on it. Manufacturers require these to be mounted no higher than six inches above the floor, with four to six inches being ideal. A pair found higher has usually been moved to clear something, and moving it back down is part of the job.

  • The lens is a surface. A film thin enough that you would not notice it on a window is enough to weaken a modulated infrared beam past the point the receiver will accept it.

  • The wire is thin and runs at floor level. The low-voltage run is usually stapled along the wall down there, where staples get driven through insulation, later shelving pinches it, and rodents reach it. Finding the break is most of that repair.

  • The units are a matched pair, sold and engineered as a kit with the sender and receiver tuned to each other. They get replaced together, and one generation's sender will not partner another's receiver.

  • Reading what the lights are telling you is its own job, because the healthy colors differ by brand and a light that looks like a fault can be the sender reporting that it has power. Our sensor repair page sets that out, brand by documented brand.

  • And one thing that is not the eyes. If both lights are steady and the door still refuses to close, the fault points upstream: at the close force, the travel limits, or the board. The photo-eye sensors and the automatic reverse test are items 20 and 21 of the 22-point inspection, so that distinction gets drawn whatever the call was booked as.

What Gets Tested Before We Leave

There are two separate safety systems on a powered door, tested two different ways. People conflate them constantly.

  • The beam test. With the door closing, something is passed through the beam near the floor, well clear of the door. The door should stop and reverse without touching anything. That tests the photo eyes.

  • The force reversal. A two-by-four laid flat on the floor in the door's path. The door should meet the wood and reverse to fully open. That tests the opener's own force system, a different mechanism with a different failure.

The safety reverse is tested before we leave, and the balance check is done on every visit. Those tests establish what the door did on the day it was tested in front of a technician. We will not tell you on the phone that your door is safe, and nobody should tell you that about a garage they have not stood in.

Phoenix Sensor FAQ

My opener has no photo eyes at all. Is that a violation?

Not of this rule. Part 1211 applies to operators manufactured on or after January 1, 1993, so a machine built earlier was never inside it. Our own boundary is firmer than the regulation: no photo eyes, no work on the motor.

Does Phoenix have its own rule about photo eyes?

No. Part 1211 is federal and reads the same on every street in the valley. Phoenix is the one jurisdiction here whose adopted code names doors on its exempt-work list, and our Phoenix page quotes it, but that is permit guidance about building work and says nothing about sensors.

Can you just make it close without them?

No. We do not bypass, disable, or defeat them.

Does one broken eye mean replacing both?

Both. They are a tuned pair and mixing generations frequently fails outright.

The door closes only if I hold the wall button down.

That is the fault state the rule describes. The opener has failed its own safety-circuit check and has fallen back to constant pressure. It is pointing at the thing to fix.

What Customers Say

Family-owned and working on garage doors in this valley since 1997.

"Very polite and professional. A very good experience."
David OstermeyerMarch 2024
See this review on Google

Where We Work

Garage door repair and service across the Phoenix metro:

See the full service area

Before you call, go and look for a pair of small units bolted near the floor.

One on each side of the opening, no higher than your shin. Whether they are there and whether they look original to the opener determines which conversation we are having. A quote over the phone is free, and if you want the garage in Phoenix looked at before anybody commits, that visit is $35.

Garage door installed on an Arizona home in Phoenix, AZ